试验室XMB240；300型球（棒）磨机技术参数

XMQ棒磨机适用于实验室湿法磨细矿石或其他物料之用。也可以将钢棒换为钢球作球磨机使用。但棒磨时，磨细产物粒度组成较均匀，过粉碎现象较小，且效率较高。一般进行矿石可选性实验研究和人工重砂磨细矿石时，宜采用棒磨。本产品由原地矿部唯一指定企业生产，执行行业标准。

XMB Rod Mill is applicable to lab. for wet fine grinding of ore and other materials. Steel ball may be used instead of steel rod in the ball mill. In rod grinding, fine product particle fractions are relatively uniform with rare occurrence of overgrinding and high efficiency. In general, rod grinding is introduced for test on ore for separability and manual fine grinding of placer materials. The product is produced by the only enterprise designated by the former Ministry of Geology and Mineral Resources, in compliance with the Industrial standards.

娱乐中心球墨铸铁筒体与大皮带轮用螺钉联为一体。筒体一端为开口，另一端为空心轴颈；两端分别承在一对托和一个主轴承上。主轴承座和托架，分别装在可转支180°的支承板上。支承板用两个轴承轴承座装在机架上。支承通过回转操纵手把及定位板，可以从水平左右偏转用22.5°、6735°、及90°，以完成装矿、排矿、倒棒和充满防锈石灰水等动作。

Drum of spheroidal graphite  cast iron and big belt pulley are connected through screws. At one end of the  drum is an opening and at the other end of it is a hollow journal. Both ends  are respectively supported on a pair of rollers and a main bearing. The main  bearing seat and bracket are respectively on the bearing plate which can rotate  for 180°. The bearing plate is installed on the frame with two bearing  pedestals. The bearings control the handle and positioning plate through  rotation. Horizontal deflection of 22.5°, 6735° and 90°can be applied to  realize ore loading, ore discharging, tamping rod, filling antirust limewater,  etc.

娱乐中心筒体右端有给矿口塞。械端有排矿口盖；工作时，用一时专门板手，按顺时针方向拧紧螺栓，使排矿口盖上的密封橡胶垫紧螺栓三、四转使盖子向外退出工6～10毫米，不用将盖子取下即可排矿。在排矿口端安设了集浆罩。在设计工作转速内完全消除子转支清洗时矿浆飞溅的现象。

There is plug of feed mouth on  the right of the drum and there is cover of discharge mouth at the end of the  machine. During the operation of the machine, use a special-purpose spanner to  tighten the bolts, to get the sealing rubber gasket on the cover of discharge  mouth to tighten the bolts for three or four rounds so that the cover can go  backward for 6～10mm. Ores can be discharged  without the cover being removed. At the end of the discharging mouth is  installed a slurry cover, which completely avoid splashing of slurry during the  washing rotating branch within the designed working speed.

电机及中间轴装在支承下面，以便与上部的重量配置均衡。传动的两级皮带每级均可调节皮带松紧，以保证全适的磨矿工作转速。

娱乐中心The motor and intermediate  shaft are installed below the bearings, so as to realize balance with the  weight above. The tension of belt can be adjusted for every grade of the  driving two-grade belt pulley, to ensure appropriate grilling speed.

67型棒磨机的皮带调整，是由支承板上T型槽滑道和中间轴座板上的长分别进行。

The pulleys of 67 rod mill are  respectively adjusted through the T-groove slide on the supporting plate and  the slot on the seat board of the intermediate shaft.

68型棒磨机的皮带调整，按下述方法进行：

The pulleys of 68 rod mill are  respectively adjusted according to the following method:

娱乐中心1、筒体皮带的调整：主要是调节中间支承的上下位置。但为了不致景响电动机皮带的松紧，须对调整螺杆作相应的调整（图1）。

娱乐中心1. To adjust drum belt, what  should be done mainly includes the adjustment of vertical position of  intermediate support. However, in order not to affect the tension of motor  belt, corresponding adjustment shall be made of the adjusting bolt (Figure 1).

娱乐中心△L—需要调整量（图示需调紧）

△L — Required adjustment amount (needing to  tighten as is shown in the figure)

S1—中间支承调整量（图示向下）

娱乐中心S1 –  Adjustment amount of intermediate support (moving downward as is shown in the  figure)

娱乐中心S2 —调整螺杆调整量（图示向下）

S2 –  Adjustment amount of adjusting bolt (moving downward as is shown in the figure)

2、电动机皮带的调整：主要是调节调整螺杆的上下，使中间轴绕中间支承转支一定位置。而为了不致影响筒体皮带的松紧。须对中间支轴承相应的调整，进行补偿。（图2）

2. To adjust motor  belt, what should be done mainly includes the adjustment of vertical position  of screw, to get the intermediate shaft to revolve around intermediate support  to a certain position. However, in order not to affect the tension of drum  belt, corresponding adjustment shall be made of the intermediate shaft for  compensation (Figure 1).

 筒体：Drum
 调整螺杆：Adjusting bolt
 中间支承：Intermediate support
 中间轴：Intermediate shaft
 距离不变：Unchanging distance
 电机：Motor

△L—需要调整量（图示需调紧）

娱乐中心△L — Required adjustment amount  (needing to tighten as is shown in the figure)

娱乐中心S1—中间支承调整量（图示向下）

S1 – Adjustment amount of intermediate  shaft (moving downward as is shown in the figure)

S2 —调整螺杆调整量（图示向下）

S2 – Adjustment amount of  adjusting bolt (moving downward as is shown in the figure)

为适应多种接矿容器的使用，折叠式接矿滑架，可以上下升降使用。机器的电器均已安装好，接上电源和地线，即可按使用要点开车运转。

To match the use of  various kinds of receiving containers, folding receiving carriage can move  upward or downward. The electric equipment of the machine has been installed.  When the power and earth wire are connected, the machine can be operated  according to instructions.